ENGINEERING SERVICES OFFERED BY ENTRICO GLOBAL

ENGINEERING SERVICES

  • BASIC ENGINEERING.
  • FEASIBILITY STUDY
  • MULTI-DISCIPLINARY DETAIL ENGINEERING.
  • PROCUREMENT ASSISTANCE
  • DRAWINGS CONVERSION TO AUTOCAD. {MANUAL TO CAD}
  • PLANT TROUBLESHOOTING.
  • HAZOP STUDY.
  • AS BUILT SERVICES / DRAFTING SERVICES.

Basic Engineering Design (BED) covering:

  • Conceptual process studies (material balances, process flowsheets,…) and preliminary plot plan.
  • Preliminary Piping and Instrument Diagrams.
  • Definition and sizing of main equipment resulting in process specifications.
  • Specification of effluents.
  • Definition of control and safety devices.
  • And, generally speaking, all the basic studies required to support a Basic Engineering Design Package (BEDP) containing all data needed by a competent contractor to perform the Detail Engineering.
  • These basic engineering studies may consist of consolidating a Process Package initiated by an external process licensor.

Front End Engineering Design (FEED) covering:

  • Mechanical data sheets of the main equipment, starting from the process specifications issued during the BED and incorporating the specific requirements of codes and standards to be applied to the project in question.
  • Thermal rating of heat exchangers.
  • Preparation of tender packages for the main equipment.
  • Development of process and utility Piping and Instrument Diagrams released for detail engineering.
  • Development of detailed plot plans and hazardous areas.
  • Elaboration of the main piping, instrument, electrical and civil works layouts.
  • And, generally speaking, all the studies to be performed before ordering the main equipment.

Detail Engineering, covering:

  • Purchasing of equipment, main and bulk.
  • Thermal rating of heat exchangers.
  • Development of Piping and Instrument Diagrams released for construction.
  • Development of detailed piping drawings, including isometrics and stress calculations.
  • Development of detailed drawings related to instrumentation, electrical facilities and civil works.
  • Management of vendor drawings.
  • Cost and schedule control.
  • Start-up procedures.

BASIC ENGINEERING PACKAGE

  • General design basis & specification for major equipment.
  • Process flow sheets, heat & material balance.
  • Preliminary PFD & P&ID development.
  • Preliminary plot plans, equipment layout & civil information drawings.
  • Electrical load list, instrument list.
  • Multi-discipline detail engineering
  • Process engineering.
  • Instrumentation engineering.
  • Electrical engineering.
  • Mechanical engineering.
  • Piping engineering.
  • Civil & structure engineering.

PROCESS ENGINEERING

  • Preparation of process flow diagrams (pfd), piping and instrument diagrams (p & id),
  • Equipment process data sheet
  • Instrument process data sheets etc.
  • Design of plant hydraulics & pumping system.
  • Process design of columns, exchanger, separators, ko drums etc.
  • Safety valve & flare network studies.
  • Utility & system packages
  • Technical bid analysis and vendor data review
  • Hazop & safety studies, commissioning & plant troubleshooting.

CIVIL & STRUCTURE ENGINEERING

  • Preparation detailed foundation drawings for equipments.
  • Design calculations and preparation of detailed structural drawings, fabrication drawings and BOM.
  • Engineering of skids and modular structures & MTO.

PIPING ENGINEERING

  • Plot plan development & conceptual pipe routing.
  • Preparation of equipment GA and piping GA
  • Preparation of isometrics with BOM / MTO.
  • Piping material selection and specification.
  • Static & dynamic stress analysis
  • Designing support specifications & drawing.
  • Plant 3-D Modeling and clash detection.
  • Extraction of isometric from 3-D Model with BOM / MTO.

MECHANICAL ENGINEERING

  • Design of complete range of process equipments. (tank, vessel, reactor)
  • Mechanical design & detailed engineering using the international codes &standard e.g. ASME sec. viii div. 1 & 2, API 650 etc.
  • Stress analysis, thermal analysis for equipment life evaluation using finite element analysis.
  • Preparation of technical bid for the projects.
  • Development of fabrication drawings & nozzle orientation drawings.

INSTRUMENTATION ENGINEERING

  • Preparation of control philosophy, detailed execution drawings.
  • Preparation of interlock logic diagrams, instrument index
  • Specifications of controls system (DCS/PLC) & field instrument.
  • Preparation of junction box termination drawings, instrument hook up drawing, wiring diagrams, cable schedule etc.
  • Preparation of cable tray / cable trench layouts design of plant.

ELECTRICAL ENGINEERING

  • Preparation of electrical single line diagram.
  • Selection of HV/LV switchgear, motor control centers.
  • Layout for switchyard / transformer layouts, switchgear / MCC room layout, battery room layouts.
  • Cable tray / trench layouts, cable routing layouts.